FM-E636T EPON OLT with 4-EPON Interfaces Module

FM-E636T EPON OLT with 4-EPON Interfaces Module



FM SKU#:SKU00213F2
Model#:FM-E636T
MFG PART#:
FM-E636T is a miniaturization and modularization GEPON OLT, broadband fiber access system platform, developed by FM. It is fully compliant to IEEE802.3-2005 and Chinese technical requirements of Ethernet Passive Optical Network (EPON). This product supports integrated access service, such as broadband surf-netting, IP voice, IPTV, CATV and etc.

Key Features

  • With Twin-star bus 10Gigabit core switch backplane, support non-blocking wire-speed switch, support 1.25G EPON optical fiber access.
  • 2.5U height, adopt full front-wiring, small size, high capacity, maximum EPON optical fiber interfaces reach up to 16.
  • Provide single main control module, single uplink module, single power supply module and 4 service interface modules.
  • Support AC/DC dual power supply, with backup power charger and alarm device, support connecting external storage battery directly to do backup power charging protection.
  • Support flexible controllable multi-cast, IGMP Proxy/Snooping and etc.
  • Support strong VLAN extension functions, including VLAN Stacking/Trunk/Translation, etc.
  • Support flexible DBA, uplink/downlink service rate-limited, precision up to 0.2% (Standard requirement<5%)
  • Adopt multi LLID and IEEE802.1p technologies, provide multi protection QoS service

    • Equipment Components

    No.ItemFull load QtyDescription
    1Equipment frame1OLT equipment frame, including 10Gigabit core switch backplane
    2Main control module (SWA)1Hot-swappable module, integrate 1 FE out of band management port, 1 debugging serial port, 10Gigabit class non-blocking switch)
    3EPON interface module (EP4)4Hot-swappable 4 EPON interfaces modules, compliant with IEEE802.3-2005 EPON technical standard, support 20km transmission distance (Standard configuration without optical module)
    4Uplink interface module(HUP)1Hot-swappable 4 GE interfaces module, SFP slot, support 4GE+10GE XFP(Standard configuration without optical module)
    5Fans module(FAN16)1Hot-swappable fans module
    6Power module(PWR)1Hot-swappable power supply module supports 220VAC/48VDC (With UPS charger). Builds dual power redundant hot backup with dual power supply

    Hardware features

    Equipment parametersDimension486mm(W)*103mm(H)*384mm(D)
    Net weight5Kg
    Power consumption≤40W
    Operating conditionTemperature:0 ~ +55℃, humidity:10 ~ 90% (non-condensed)
    Storing conditionTemperature:-25 ~ +70℃, humidity:10 ~ 90% (non-condensed)
    Power supplyDC36 ~ 75 VDC
    AC176 ~ 264 VAC
    Equipment interfaceUplink Ethernet interface1*10GE(XFP connector), 4*GE interfaces (GE or SFP connectors)
    EPON interface16*EPON SFP interfaces
    Console debugging interface1 interface, compliant with RS232 technical standard
    Out-of-band management interface1 interface, compliant with 100Base-TX technical standard
    Monitor and alarm interface1 interface, compliant with RS485 technical standard (Support sub-node monitor )

    Advanced features

    Switch function10Gigabit switch backplane (Switch capability reach up to 60Gbps), non-blocking wire-speed switch ability
    16K MAC address table, support 2K multicast table, support 4K VLAN (802.1Q)
    Up to 1*10GE, 4* uplink GE aggregation (IEEE 802.ad), support maximum 5 aggregation groups, support port mirroring based on output interface
    VLANSupport IEEE 802.1Q VLAN, support 4K concurrent VLAN
    Strong VLAN extension functions, support VLAN Stacking/Trunk/Translation and flexible QinQ, etc
    RSTPSupport STP, RSTP
    IGMPSupport IGMPv1/v2 protocol, support IGMP Snooping/Proxy, support controllable multicast
    QoS and ACLSupport CAR(Committed Access Rate), flow rate limit granularity is 64Kbps,
    Support priority level remarking based on port ID, MAC address, VLAN, 802.1p, DiffServ and/or IP ToS priority
    Support flexible queue scheduling algorithm, support port-based and queue-based configuration simultaneously, support three queue dispatch strategies, such as SP(Strict Priority),WRR(Weighted Round Robin) and hybrid mode(SP+WRR)
    Provide illegal frame filter and packet filter that based on sources MAC(Media Access Control)address, sources IP address, destination IP address, port, etc. Support QoS Profile management, allow user draw up QoS service plan
    Broadcast storm suppressionSupport broadcast, multicast and DLF broadcast storm suppression, suppression based on setting PPS
    Flow controlSupport IEEE 802.3x flow control in Full duplex mode, support backpressure flow control in half duplex mode
    Encryption and securitySupport LLID MAC address bundling, control the registration of ONU. Prevent illegal ONU deceive
    Support ONU inter-separation control within same EPON network Support encrypted start to control configuration
    Link testSupport EPON network link diagnosis by Ping and Link test
    Configuration recoverySupport ONU off line configuration, auto-configuration when registered
    ManagementFTP, Telnet, Console
    Support in/out-of-band management, support SNMPv1/v2, support IEEE802.3ah OAM
    Management functionSupport equipment configuration management, performance management, fault management, sources management, safety management and etc.
    Support ONU remote management, remote mass configuration download, software remote auto-update
    Support ONU offline configuration, auto-configuration when registered
    Support ONU line diagnosis and distance measuring
    Redundant backupSupport AC/DC dual power protection

    评论

    发表评论

    此博客中的热门博文

    Common Armored Fiber Optic Cables

      Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
    阅读全文

    what the Differences Between FBT Splitter and PLC Splitter

      In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
    阅读全文

    Introduction of Optical Fiber Couplers and How Do They Work?

     What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
    阅读全文