Why the MTP Connector is Going to Change the Cabling World

by www.fiber-mart.com
Until June of 2010, before the ratification of the IEEE 802.3ba, the MTP® connector’s major benefit was installation speed and reduction of bulk cordage. The 802.3ba standard offered a roadmap for manufacturers to develop 40/100G Ethernet projects. Arguably one of the most dynamic changes in the cabling infrastructure world, this standard called for the use of the MTP (MPO style) for multimode fiber cabling infrastructures.
 
MTP / MPO - A Game Changer
 
Before I get into telling you why it's going to change the world, I should first explain MTP vs. MPO style connector. MTP is a popular brand name of an MPO style connector. In other words, MPO is the official name of the type of connector, but MTP is a very popular brand name. Much like “Band-Aid” is to “adhesive bandage."
 
The 802.3ba standard calls for the use of the MTP connector in multimode fiber cabling infrastructures. The main reason for this is cost.
 
40 and 100G Ethernet cannot be obtained utilizing standard short range optics (transceivers) that utilize VCSEL (Vertical Cavity Surface Emitting Lasers), running over a standard serial connection. A serial connection is when one fiber is used for transmit and the other fiber used for receive. This is the standard duplex connection that most are familiar with in fiber cabling.
 
Enter “parallel optics” - this is where multiple fibers are aggregated to transmit multiple 10G signals each. For 40G there will be (4) 10G fibers transmitting and (4) 10G signals coming back (Rx and Tx). This short video does a great job in explaining how this works.
 
 
So how is this going to change the cabling world?
Well, most data center fiber infrastructures are based on a duplex, or serial, connection system. LC, SC and ST connectors are prominent. This changeover to the MTP will be required to run 40/100G Ethernet speeds (unless using expensive LX optics which are cost prohibitive to most).
 
This turns the cabling infrastructure upside down. MTP’s need to be incorporated into the mix - and the sooner the better! Many times, new hardware is purchased and the cabling is an afterthought. If this is the case, then there will be a rude awakening if one plans on using multimode fiber. Do your research before investing in new cabling now...it will pay off later!

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文