WHAT IS A FIBER OPTIC SPLICE TRAY?

by www.fiber-mart.com
Splice trays are necessary for holding and protecting individual fusion splices or mechanical splices.
 
Splice trays are available for all different kinds of splices, such as mechanical splices from 3M, Corning, AMP and Siemon company, bare fusion splices and heat-shrink fusion splices, and so on.
 
Normally splice trays should be matched to the type of splice used. A splice tray designed for holding mechanical splices usually can not be used for bare fiber fusion splices or heat-shrink fusion splices. Although there are splice holding chips you can purchase to make them work, it is not the ideal way.
 
Standard splice trays can hold up to 12 splices and you can use several splice trays together for higher strand number fiber optic cables. The splice tray has room for mounting fiber splices and excess fibers.
 
Fiber loose tubes enter the splice tray at one end and are secured to the splice tray. The loose tube stops at the splice tray end and individual fibers are exposed and spliced inside the splice tray.
 
NOTE: Bare fibers without protection tubes should never be exposed outside of a splice tray. When splicing a large fiber optic cable with more than 12 fiber strands, proper buffer tube splitters should be used when routing bare fibers to another splice tray.
 
Be very careful when mounting the splices inside the tray. Minimum fiber bending radius requirement should always be observed.

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文