CWDM SFP+ Transceiver

CWDM-SFP10G-80


The CWDM-SFP10G-80 1470-1610nm series optical transceiver is designed for fiber communications application up to 10G, which fully compliant with the specification of SFP+ MSA SFF-8431.This module is designed for single mode fiber and operates at a nominal wavelength of CWDM wavelength. There are eight center wavelengths available from 1470nm to 1610nm, with each step 20nm. A guaranteed optical link budget of 23 dB is offered.The module is with the SFP+ connector to allow hot plug capability. Only single 3.3V power supply is needed. The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver.This module provides digital diagnostic functions via a 2-wire serial interface as defined by the SFF-8472 specification.

Key Features

  • Hot-Pluggable SFP+ footprint
  • 8-Wavelength CWDM DFB Transmitter from 1470nm to 1610nm, with step 20nm
  • Average Output Power:0~4dBm
  • Receiver Sensitivity:-23dBm
  • 23dB Power Budget at Least
  • Duplex LC connector
  • Power Dissipation < 2.5W
  • Dispersion tolerance 1600ps/nm
  • Build-in digital diagnostic functions
  • Compliant with SFF-8431 MSA
  • Compliant with SFF-8432 MSA
  • Compliant with SFF-8472 MSA
  • Case operation temperature range 0℃ to 70℃

Applications

  • 10GBASE-ZR/ZW
  • 10G FC
  • Other Optical Link

Ordering Information

Part No.Data Rate (Gbps)Wavelength (nm)TX Power (dBm)Re Sens. (dBm)Transmission Distance/Optical BudgetOptical ComponentsTemp. RangeDigital DiagnosticsApplication
CSFP-10GXX-109.95~11.1G1270 ~1330-5~0﹤-1510km/4.5dBCWDM DFB/PIN0~70℃YesEth,10GFC
CSFP-10GXX-109.95~11.1G1350 ~1610-5~0﹤-1510km/4.5dBCWDM DFB/PIN0~70℃YesEth,10GFC
CSFP-10GXX-209.95~11.1G1270 ~1330-5~0﹤-1520km/11.5dBCWDM DFB/PIN0~70℃YesEth,10GFC
CSFP-10GXX-209.95~11.1G1350 ~1450-5~0﹤-1520km/11.5dBCWDM DFB/PIN0~70℃YesEth,10GFC
CSFP-10GXX-409.95~11.1G1270 ~1450-1~4﹤-15.840km/16dBCWDM DFB/PIN0~70℃YesEth,10GFC
CSFP-10GXX-409.95~11.1G1470 ~1610-1~4﹤-15.840km/16dBCWDM EML/PIN0~70℃YesEth,10GFC
CSFP-10GXX-609.95~11.1G1270 ~1450--60km/22dBCWDM DFB/PIN0~70℃YesEth,10GFC
CSFP-10GXX-609.95~11.1G1470 ~1610--60km/22dBCWDM DFB/PIN0~70℃YesEth,10GFC
CSFP-10GXX-809.95~11.1G1470 ~16100~4﹤-2380km/23dBCWDM EML/APD0~70℃YesEth,10GFC
Notes
  • XX means CWDM wavelength (27 = 1270nm, 29 =1290nm, 31 = 1310nm, 61 = 1610nm, etc., with step 20nm)
  • xx means compatible brand. (For example: CO= Cisco, JU=Juniper, FD=Foundry, EX=Extreme, NE=Netgear,etc. The two characters are short for compatible brand.)

Packaging

  • Antistatic bag
  • Packed on pallets in a box(Default Customer Options)
  • Specific Labels as Request
  • Seperate white Box for each transceiver

OEM and ODM

Combining our extensive design and engineering capability in optical transceiver industry, with our competitive advantages from integrated manufacturing capability, internal supply chain, and cost competitive and scalable operation infrastructure, Fiber-Mart provides OEM, ODM, and contract manufacturing service to world leading customers with our manufacturing facilities in China.We are also mainly engaged in providing complete sets of optoelectronic device solutions to gain more brand extensions and influence for Fiber-Mart in the world.
  • OEM/ODM order is available
  • We can supply CWDM-SFP10G-80 according to your requirements, and design CWDM-SFP10G-80 label and packaging for your company.We welcome any inquiry for customized CWDM SFP+ optical transceiver.

Order Procedure

  • Please contact us with any special requirements you may have, we can help you create a custom solution to meet almost any application. Our engineer will review the project and provide a quotation within 1-2 business days.
    a. Email (sales@fiber-mart.com) a rough sketch to a detailed drawing.
    b. Our engineer will review the project and provide a quotation within 24 hours.
    c. We can arrange production as low as 1 piece and as high as 1,000 pieces in 1~4 business days once an order is placed.

 

  • Shipment
  • International Express: Fedex, DHL, UPS, TNT and EMS.If you have another preferred carrier, please notify us in advance.
    FedEx Overnight: It will take 1-3 business days (weekends and holidays excepted) for delivery.
    DHL: It will take 2-4 business days (weekends and holidays excepted) for delivery. For Spain, Italy, Brazil and some other countries, items will take longer time to arrive due to customs clearance period.

 

  • Save Cost By Buying 10G CWDM SFP+ From Original Manufacturer Fiber-Mart Directly.
  • Fiber-Mart is an professional manufacturer & supplier of 10G CWDM SFP+ transceivers. All of our 10G CWDM SFP+ transceivers are tested in-house prior to shipping to guarantee that they will arrive in perfect physical and working condition. We guarantee 10G CWDM SFP+ transceivers to work in your system and all of our 10G CWDM SFP+ transceivers come with a lifetime advance replacement warranty. If you have questions about 10G CWDM SFP+ optics, please feel free to contact us at sales@fiber-mart.com.


    • In fiber-optic communications, Coarse Wavelength Division Multiplexing (CWDM), a WDM technology which multiplexes a number of optical carrier signals onto a single optical fiber by using different wavelengths (i.e., colors) of laser light. Effective CWDM realizations with uncooled lasers and wide passband filters a nominal central wavelength spacing of not less than 20nm. Total source wavelength variation of the order of ± 6-7nm is expected to be compatible with current filter technologies. In 2002 the ITU standardized a channel spacing grid for use with CWDM (ITU-T G.694.2), using the wavelengths from 1270nm through 1610nm with a channel spacing of 20nm. Many CWDM wavelengths below 1470nm are considered "unusable" on older G.652 (dotten line) specification fibers, due to the increased attenuation in the 1270–1470nm bands. Newer fibers which conform to the G.652.C and G.652.D (full line) standards, such as Corning SMF-28e and Samsung Widepass nearly eliminate the "water peak" attenuation peak and allow for full operation of all 18 ITU CWDM channels in metropolitan networks.

CWDM Wave Grid

BandNomenclatureWavelength(nm)
Min.Typ.Max.
O-band OriginalA126412701277.5
B128412901297.5
C130413101317.5
D132413301337.5
E134413501357.5
E-band ExtendedF136413701377.5
G138413901397.5
H140414101417.5
I142414301437.5
J144414501457.5
S-band Short WavelengthK146414701477.5
L148414901497.5
M150415101517.5
N152415301537.5
C-band ConventionalO154415501557.5
L-band Long WavelengthP156415701577.5
Q158415901597.5
R160416101617.5

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文