16 Slots Dual Power Supply 19' 4U rack-mount chassis for 4V /8V /16V cards

https://www.fiber-mart.com/16-slots-dual-power-supply-19-4u-rackmount-chassis-for-4v-8v-16v-cards-p-1495.html

FM SKU#:SKU00039R
Model#:FM-4U-2A
MFG PART#:

16 Slots Dual Power Supply 19' 4U rack-mount chassis for 4V /8V /16V cards

The 16 Slots Dual Power Supply 19' 4U rack-mount chassis for 4V /8V /16V cards can akes your installation easier. The chassis employs a 220 VAC/48 VDC Switch Mode Power Supply(SMPS) design, which reduces the possibility of a single module failure causing a shutdown or a major failure of other modules within the chassis. The high reliability and stability ensures that if one module shuts down, the operation of the other modules remains unimpaired. 0ne or two air-cooling fans are installed inside to further strengthen the superior performance of the system and eliminate the necessity for periodic maintenance. Status information can be read through the LED indicators on the installed modules. All of the modules installed in the chassis are hot swappable, which makes it unnecessary to power-down.

Key Features

Panel material: Iron
It can support 16 pcs of 4 Channel Optic Video Multiplexer .
Standard:IEEE802.3 10/100 Base T Ethernet, IEEE802.3U, 100Base V TX/FX Fast Ethernet, IEEE802.3 x Flow control, IEEE802.3.1q VLAN, IEEE802.1p QoS, IEEE802.1d Spanning Tree
Power configuration: Dual power supply for warm backup mode
Hot Swap Support for the Multiplexers to ensure a flexible connection
Equipped with a second, redundant Power Supply for maximum stability and reliability
 
Number of slots16
Video Multiplexers adapter16 Slots chassis Card Type Video Multiplexers
Power inAC 100V~260V, 50~60Hz; OR DC 48V
Power outDC + 5V, 24A(dual power)
Diameter of DC plug2.5/5.5mm
Pipple≤50Mv
Noise≤50Mv
Protection of power supplycircuit-breaker when over voltage, circuit-breaker when over flow,circuit-breaker when short circuit
Operating Temperature0ºC~50ºC
Storage Temperature0ºC~85ºC
LCD Displaying160×32 Pixels
Relative Humidity5%~95%
DimensionsL485, W231,H90 mm; 19 inches 2U

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文