How Fiber Transmission Works

by www.fiber-mart.com
Light rays are modulated into digital pulses with a laser or LED and move along the core without penetrating the cladding. The light stays confined to the core because the cladding has a lower refractive index, which is the measure of a material’s ability to bend light.
 
This results in the phenomenon of total internal reflection (TIR), which happens when a propagating wave strikes a boundary between two mediums (in this case, the core and the cladding) at an angle larger than the fiber’s critical angle. If the refractive index is lower on the other side of the boundary (the cladding) and the incident angle is greater than the critical angle, the wave cannot pass through and is entirely reflected.
 
Signal Attenuation
 
Signal attenuation in an optical fiber is measured in decibels (dB). Fiber optic cable specifications express loss as attenuation per 1 km length (dB/km). This value is multiplied by the total length of the optical fiber in kilometers to determine the fiber’s total loss in dB.
 
Light traveling in an optical fiber is not 100% efficient; there are several causes of signal attenuation. The loss of power also depends on the wavelength of the light and on the propagating material. For silica glass, the shorter wavelengths are attenuated the most. The lowest loss occurs at the 1550 nm wavelength, which is commonly used for long-distance transmissions.
 
Simplex OM3 10G 50/125 Multimode Fiber Optic Patch Cable
 
Loss Inherent to Fiber: Light loss in a fiber that cannot be eliminated during the fabrication process is due to impurities in the glass and the absorption of light at the molecular level. Loss of light due to variations in optical density, composition, and molecular structure is called Rayleigh scattering. Rays of light encountering these variations and impurities are scattered in many directions and lost.
 
The absorption of light at the molecular level in fiber is mainly due to contaminants in glass such as water molecules. The ingress of water molecules into an optical fiber is one of the main factors contributing to the fiber’s increased attenuation as it ages. Silica glass’s (Si02) molecular resonance absorption also contributes to some light loss.
 
Loss Resulting from Fiber Fabrication: Inconsistencies in the fiber manufacturing process will result in the loss of light. For example, a 0.1% change in the core diameter can result in a 10 dB loss per kilometer. Precise tolerances must be maintained throughout the manufacturing of the fiber to minimize loss.

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文