40G & 100G Optical Transceivers Basics

by www.fiber-mart.com
40G and 100G have two main types in the data center. Short reach (SR4) for ~100 meters transmission on multimode fiber and Long Reach (LR4) for 100 meters to 10km using single-mode fiber. We can use SR/LR transceivers to connect compute clusters and various switches layers in data centers. 40G transceivers are typically deployed as four 10G lanes in QSFP or CFP MSAs. 40G SR transceiver uses 8 multi-mode fibers, VCSEL lasers, and the QSFP MSA. Using edge-emitting lasers and multiplexes the four 10G lanes onto two single-mode fibers, 40G LR4 reach a 10km distance per CFP MSA, CFP/2 or QSFP28 MSAs. The 40G SR4 and LR4 transceivers can be used in the same QSFP switch port without any issues.
 
A recent report from market research company LightCounting talks about the 40G & 100G optical transceivers basics, here are the details.
 
100G SR10 transceivers use 20 multi-mode fibers, VCSELs and the CXP MSA, the 100G LR4 transceivers uses CFP form and 2 single-mode fibers. The 100G SR10 CXP transceivers and AOCs are typically designed for the link of large aggregation and core switches at <50 meters. Since 2008, 40G QSFP transceivers and AOCs have been available, but until 2012, several transceiver companies announced CXP 100G SR transceivers.

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文