What do Cat5e, Cat6, and Cat6a have in common?

They each utilize 4 twisted pairs in a common jacket. They use the same style RJ-45 jacks and plugs. And, they are each limited to a cable length of 100 meters including the length of the patch cables on either end of the link. The parts are interchangeable, so you can use a Cat5e patch cable with Cat6 house cabling. Your system will just perform at the level of the lowest link, in this case the Cat5e patch cable.
 
So what’s the difference?
 
Better transmission performance. With each upgrade in cable, there is less signal loss, less cross talk, and more bandwidth. And of course, more cost. So the important question is: What exactly am I getting for my money? Rather than talk about near-end-cross-talk requirements or SNR ratios, let’s talk about what each cable delivers in terms of Ethernet performance.
 
Cat5e:   Gigabit Ethernet up to 100 meters   10 Gigabit Ethernet up to 45 meters
 
Cat6:    Gigabit Ethernet up to 100 meters   10 Gigabit Ethernet up to 55 meters
 
Cat6a:   Gigabit Ethernet up to 100 meters 10 Gigabit Ethernet up to 100 meters
 
All three support gigabit, which is enough for most networks. 10 Gigabit, when it is deployed, is typically utilized for aggregation links between switches and not for workstations. Although it is unlikely an enterprise will require 10 gigabit to the workstations, certainly it is reasonable to design a new system with future needs in mind. In this case, the 10 gigabit capacities of Cat5e and Cat6 are problematic. Since data closets are located based on an assumption that workstation lines can be up to 100 meters, the shorter length limitation for Cat5e and Cat6 make them undesirable. That leaves Cat6a as the cabling of choice for future proofing.

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文