What is Pre-terminated MPO MTP Cables?

 by www.fiber-mart.com

The MPO fiber patch cord adopts MPO (Multi-fiberPushOn) connector. The precise connection of the patch cord is realized through two guide holes and guide pins with a diameter of 0.7mm on the left and right of the end face of the ferrule. At present, the most widely used is the 12-pin MPO connector. 12-core to 24-core MPO fiber optic patch cords, with good performance and low loss, are widely used in FTTX, wide area networks (WANs), local area networks (LANs), telecom networks, 40/100/200G network solutions and other wiring environments which are best solutions to realize high density and high bandwidth network.
 
The Pre-Terminated MTP/MPO Technology is with polarity Classification. The three polarity methods ensure accurate bidirectional configuration - Type A, Type B, Type C. Each end of the MTP/MPO trunk fiber patch cord is equipped with an MTP/MPO connector.
 
Pre-terminated MPO/MTP Trunk Cables and Breakout Fiber Patch Cord
 
MPO/MTP trunk fiber patch cord are connected with MPO/MTP connectors at the both ends. And MPO/MTP breakout fiber jumpers are one side connected MPO/MTP connector and the other side with LC/SC connector.
 
MPO/MTP cables are designed for high-density Gigabit Ethernet and Fiber Channel applications which are with pre-terminated, high-performance features. The pre-terminated MPO/MTP patch cables can realize high-speed, high-density, wide-bandwidth transmission to meet the needs of future network development. UnitekFiber provides a variety of conventional or customized pre-terminated MPO/MTP patch cables, including MPO/MTP trunk cables and MPO/MTP breakout fiber patch cords. Our pre-terminated MPO/MTP fiber patch cables are available in single-mode, multi-mode and 10G OM3/OM4. 10G OM3/OM4 MPO/MTP fiber patch cables are widely used in today's data center application.

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文