Some Questions About Fiber Optic Cable

 What is fiber optic cable?

 

A fiber optic cable is really a network cable which contains strands of glass fibers in a insulated casing. These cables are equipped for long distance and very high bandwidth (gigabit speed) network communications. If you want to know more info about fiber optic cable specifications, you can visit the Fiber-mart.com "Fiber Optic Cable Tutorial" within our tutorial.

 

There are a couple of types of optical fiber cables, Single-mode VS Multimode?

 

Single-mode fiber provides you with a greater transmission rate and as much as 50 times more distance than multimode, it is more expensive. Single-mode fiber includes a smaller core than multimode fiber-typically Five to ten microns. Merely a single lightwave can be transmitted at a with time. The small core and single lightwave virtually eliminate any distortion that may derive from overlapping light pulses, providing the least signal attenuation and also the highest transmission speeds associated with a fiber cable type.

 

From data and voice to security and videoconferencing, a lot of today's IT infrastructure services depend on fiber optics to transmit information faster, farther, as well as in greater amounts than in the past. So fiber optics are more and more popularity within our internet. This post will attempt to reply to a few of the questions about fiber optic cable.

 

Multimode fiber gives you high bandwidth at high speeds over long distances. Lightwave are dispersed into numerous paths, or modes, because they travel through the cable's core. Typical multimode fiber core diameters are 50, 62.5, and 100 micrometers. However, in long cable runs (greater than 3000 feet (914.4 ml), multiple paths of light can cause signal distortion at the receiving end, leading to an unclear and incomplete data transmission. For example, you can test to check the single mode duplex fiber vs multimode duplex fiber optic cable, and well know their different.

 

Relationship between fiber optic cable and fiber patch cord:

 

A fiber patch cord is really a fiber optic cable capped at either end with connectors that permit so that it is rapidly and conveniently linked to CATV, an optical switch or other telecommunication equipment. Its thick layer of protection can be used to connect the optical transmitter, receiver, and the terminal box. This is known as "interconnect-style cabling".

 

What types of connectors ought to be used?

 

There are a number of connector styles available on the market including LC, FC, MT-RJ, ST and SC. There are also MT/MTP style connectors which will accommodate up to 12 strands of fiber and occupy far less space than other connectors. This connector is intended for use with indoor loose tube no-gel cable constructions. However, typically the most popular connectors are SC, which push in then click when seated, and ST, also known as bayonet style, which are pushed in and twisted to lock. That needs to be considered when creating product selections.

 

What kind of jacket rating and kind do you require?

 

Fiber cable jackets are available in many styles. For example, fiber could be Indoor only, Outdoor only, Indoor/Outdoor, Tactical also it can also provide Plenum or Riser ratings.

 

Jacket color is relatively standardized.

 

a) Multimode = Orange

 

b) 50/125um 10G = Aqua

 

c) Single Mode = Yellow

 

d) Indoor/Outdoor or Outdoor = Black

 

e) Custom jacket colors are also available for indoor fiber cables

 

Whether you are your residential or commercial environment. Fiber-mart.com provides a wide selection of fiber cables, and other fiber optic cables related prodcuts, such as fiber patch cable, fiber optic connector, fiber transceiver. No matter how complex or simple your installation needs are, we've the expertise to offer you the right products and knowledge for both your fiber optic cable, custom fiber optic assembly and fiber optic connector needs.

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文