Gigabit PoE Switch vs Normal Switch

by www.fiber-mart.com
The telecommunication industry has always been developing with leaps and bounds and technology changes with each passing day. For common people with few network knowledge, the evolving optional network devices like PoE switch can be a big puzzle. What is PoE? What is the distinction of gigabit PoE switch vs normal switch? Read this article for reference.
 
What Are PoE and PoE Switch?
PoE, abbreviation of Power over Ethernet, is a technology that enables Ethernet cable to supply power. Thus power sourcing equipment (PSE) can transmit both data and power to powered devices (PD) simultaneously via one single cable. PoE has two standards available on network switch: IEEE 802.3af/at. The former orginal PoE standard is defined in 2003, which provides 15.4 W power budget to PDs (12.95 W available for accessing). The latter PoE+/PoE Plus standard defined in 2009 provides up to 30 W (25.5 W) power.
 
PoE switch is one of the two types of PSE for PoE implement: endspan switch and midspan PoE injector. To enhance network resiliency, gigabit PoE switches provided by FS.COM are highly compatible IEEE 802.3af/at managed PoE+ switches. For example, S1130-8T2F managed gigabit 8 port PoE switch with 2 SFP ports can connect to gigabit Ethernet network while S1600-48T4S 48 port PoE switch can use the SFP+ ports to connect with 10gbe switch for higher performance data transfer.
 
PoE Switch vs Normal Switch: What’s the Difference?
In a word, PoE switch and normal switch differ from PoE accessibility. A regular Ethernet switch is not PoE enabled to supply power for end users over Ethernet. Therefore the user requires one extra cable to connect power outlets. However a normal switch can also become PoE ready by employing a midspan injector between the switch and PDs. The injector will add electrical power while receiving data signal from Ethernet switch end cable, and then deliver both data and power to PDs. But in this circumstance the injector also needs a wire for power. When using gigabit PoE switch, only one power cable is required. Then the PDs can be directly plugged into the PoE gigabit switch port for both data transmission and power supply. The illustration and table below list the differences of employing PoE switch vs normal switch while adding PoE to network.
 
What Are the Advantages of PoE Switch?
As mentioned above, PoE switch differs from normal switch for supplying power to PDs in the meantime of data delivery. Though the normal switch system can also acquire PoE by installing injector, PoE endspan has the superiority of direct Power over Ethernet ability. Counting to this, gigabit PoE switch owns edges over normal switch as follows. First, it enables PDs like IP surveillance cameras to be placed almost anywhere: on the ceiling, concealed in a wall, or even underwater while only one cable is needed to run to them. Second, it saves extra expanse and time for power cabling and injector installation. Third, with simplified cabling of all PDs directly connected to gigabit PoE switch, the data center is easy for management and control. Besides, PoE gigabit switch itself is designed with advanced features like high-performance hardware with software, auto-sensing PoE compatibility, strong network security and environmental adaptability.
 
Conclusion
Gigabit PoE switch can supply power to PDs in the meantime of data transmission via one single Ethernet cable while normal switch can only send data to them. For PoE implement, normal switch requires a power-on auxiliary injector as midspan between switch and powered devices. Thus PoE switch owns advantages of direct PoE connection, easy and flexible placement, cost-efficiency, simplified management and etc. For any applications of IP surveillance cameras, VoIP phones and wireless APs, PoE switch over normal switch is a good solution to go.
 

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文