Should We Use Third-Party Compatible SFP Transceiver?

Many customers tend to use third-party compatible Cisco SFP transceivers to save costs on these expensive modules. But there maybe a problem that the Cisco’s new line switches do not support third-party SFPs. When inserting an SFP transceiver into Cisco switches to connect network backbone, you will find it doesn’t match an official Cisco product. Then you will stumble across the following error:
 
%PHY-4-UNSUPPORTED_TRANSCEIVER: Unsupported transceiver found in Gi1/0/0
%GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR: GBIC in port 65538 has bad crc
 
The Catalyst switch disables the GBIC port. That’s because Cisco Catalyst switches are configured by default not to work with non-Cisco SFPs. When a third-party SFP inserted into the port, the switch immediately recognize it doesn’t match. And it will throw the above error message and disables the port.
 
Except the error, Cisco tends to be very strict about the warranty requirements for the third-party components including SFP transceivers. The details are as following: When Cisco determines that a fault or defect can be traced to the use of third-party transceivers installed by a customer or reseller, then, at Cisco’s discretion, Cisco may withhold support under warranty or a Cisco support program. In the course of providing support for a Cisco networking product Cisco may require that the end user install Cisco transceivers if Cisco determines that removing third-party parts will assist Cisco in diagnosing the cause of a support issue.
 
That means if you use a third-party transceiver and it causes actual damage. Cisco may refuse warranty support. If the transceiver is merely suspected of being at fault, they may refuse support until you install a supported Cisco-branded transceiver.
 
Now you may ask “Are the third-party compatible transceivers safe?”. The answer is yes. Most third-party transceivers are made and assembled in exactly the same plants assembling officially-branded transceivers. In a matter of speaking, an official Cisco transceiver and a third-party transceiver are the same, aside from the branding. In fact, the transceivers don’t have any real way of failing that would also damage a switch. So there is no problem to use third-party compatible transceiver.
 
Compatible SFP transceiver modules offered by fiber-mart.com are third-party and fully compatible with major brands (Cisco, HP, NETGEAR, Finisar, Juniper, etc.) and backed by a Lifetime Warranty. fiber-mart.com have a large selection of compatible SFP modules in stock and can ship within 24 hours.
 

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文