OM5 Fiber for the Application of SWDM

The upgraded OM3 and OM4 have been widely applied in data centers and other high-speed applications in the past few years. Now, OM5, which allows a higher range and transmission speed by SWDM (Short Wave Division Multiplexing) technology, is available in fiber-mart.com.
 
OM5 was chosen to be the new standard for the wideband multimode fiber in the upcoming 3rd edition of the ISO/IEC 11801. The acceptance of this standard is a milestone for the fiber cabling performance category because it extends the benefits of this revolutionary multimode fiber within connected buildings and data centers worldwide.
OM4 fiber cable
Compared with OM3 and OM4, which are suitable for transmission in the range of 850nm wavelength, the new optical cabling class OM5 can operate within a range of 850nm to 950nm, thus increasing the performance and the quality of connectivity in your data center.
 
The advantages of OM5 fibers can be summarized as follow:
 
1. Excellent performance and quality of connectivity for your data center.
 
2. Higher range and transmission speed through SWDM technology.
 
3. Transmission rate up to 100 Gbit/s with only 2 fibers (instead of 8 fibers).
 
4. OM5 cabling supports all legacy applications and is fully compatible with OM3 and OM4 cabling.
 
At fiber-mart.com, we can offer our customer industry standard flammability rating LSZH/Riser jacket fiber patch cables with connector types of LC-LC and SC-SC and customized length. Also, all the OM5 cables from fiber-mart.com are well packaged and 100% optically tested for end face and insertion loss to ensure high quality. 

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文