Understand 100G Transceivers Transmission Principles

Changes to transmission speeds and expansion in data center capacities have driven the 100 Gigabit Ethernet. IHS Infonetics reports that by 2019, 100G Ethernet will make up more than 50 percent of data center optical transceiver transmissions. For 100G transceivers, there are 100GBASE-SR4, SR10 and PSM4 for short-distance transmission and 100GBASE-CWDM4, LR4 and ER4 for long-distance transmission.
 
100G Transceivers Transmission Principles
100GBASE-SR4 QSFP28 transceiver uses a 12-fiber MMF strand MTP/MPO cable for 100m connectivity (4 Tx and 4 Rx, each lane providing 25 Gbps of throughput over 850nm wavelength).
Cisco CFP100GSR10 Compatible 100GBASESR10 850nm 150m Transceiver
100GBASE-SR10 CFP optics use a 2×12-fiber or 24-fiber MMF strand MPO/MTP cable for 150m connectivity (10 Tx and 10 Rx, each lane providing 10 Gbps of throughput over 850nm wavelength).
 
100GBASE-PSM4 QSFP28 transceiver uses a 12-fiber SMF strand MTP/MPO cable for 500m connectivity (4 Tx and 4 Rx, each lane providing 25 Gbps of throughput over 1310nm wavelength).
 
100GBASE-CWDM4 QSFP28 transceiver provides aggregated 100G data rate over 2 km on SMF. The four optical signals from the four wavelengths are multiplexed and coupled to SMF through an industry-standard LC connector, and on the receive side, the demultiplexer splits the four wavelengths apart.
 
100GBASE-LR4 transceivers provide 100G data rate over 10 km on SMF. The four optical signals from the four wavelengths are multiplexed and coupled to SMF through an industry-standard LC connector, and on the receive side, the demultiplexer splits the four wavelengths apart.
 
Note: fiber-mart also provides Juniper compatible CFP LR4 modules with duplex SC interface.
 
100GBASE-ER4 transceivers provide 100G data rate over 40 km on SMF. The four optical signals from the four wavelengths are multiplexed and coupled to SMF through an industry-standard LC connector, and on the receive side, the demultiplexer splits the four wavelengths apart.
Cisco QSFP QSFP+ Transceiver
100G Transceivers Custom Information
For 100G transceivers, FS also provides custom service. The form factor, interface, type, label and compatible brand can be customized by your special requirements.
 
For more details about our 100G QSFP28 and CFP/CFP2/CFP4 transceiver modules, please visit our site www.fiber-mart.com.

评论

发表评论

此博客中的热门博文

Common Armored Fiber Optic Cables

  Armored fiber optic cables are often installed in a network for added mechanical protection, as they have extra reinforcing in the cable housing to prevent damage. Two types of armored fiber optic cables exist: interlocking and corrugated. Interlocking armor is an aluminum armor that is helically wrapped around the cable and found in indoor and indoor/outdoor cables. It offers ruggedness and superior crush resistance. Corrugated armor is a coated steel tape folded around the cable longitudinally. It is found in outdoor cables and offers extra mechanical and rodent protection.   The Structure of an Armored Fiber Optic Cable In basic armored fiber cable designs, the outer sleeve provides protection against wind, solvents, and abrasion. This outer sleeve is usually made of plastic such as polyethylene. The next layer between the sleeve and the inner jacket is an armoring layer of materials that are difficult to cut, chew, or bu
阅读全文

what the Differences Between FBT Splitter and PLC Splitter

  In FTTx and PON architectures, optical splitter plays an increasingly significant role to create a variety of point-to-multipoint fiber optic networks. But do you know what is a fiber optic splitter? In fact, a fiber optic splitter is a passive optical device that can split or separate an incident light beam into two or more light beams. Basically, there are two types of fiber splitter classified by their working principle: fused biconical taper splitter (FBT splitter) and planar lightwave circuit splitter (PLC splitter). You may have one question: what’s the difference between them and shall we use FBT or PLC splitter?   What Is FBT Splitter? FBT splitter is based on a traditional technology to weld several fiber together from side of the fiber. Fibers are aligned by heating for a specific location and length. Because the fused fibers are very fragile, they are protected by a glass tube made of epoxy and silica powder. And then a stainless steel tube covers the inner glass tu
阅读全文

Introduction of Optical Fiber Couplers and How Do They Work?

 What are optical fiber couplers? A fiber optic coupler can be defined as an optical component used with one or more input fibers and several output fibers in fiber optic systems. A coupler essentially puts two or more cores of fibers together to connect. The simple coupler is the fused fiber 2x2 coupler. Couplers are used as multiplexers that are resistant to certain wavelengths. A fiber output depends on the wavelength of light and the frequency of polarization. The fiber refractive index also plays a significant role in the performance. Let’s checkout how do optic couplers work to understand this better. How do fiber optic couplers work? Either fiber optic couplers separate optical signals into multiple paths or combine multiple signals in one direction. Optical signals are more complicated than electrical signals, making it more difficult to design optical couplers than their electrical copy. Unlike electrical currents, the optical signal consists of a stream of signal carriers, in
阅读全文